JC50-20-A JD50/80-98R JC50-16-A
PRODUCT SPECIFICATIONS
PRODUCT SPECIFICATIONS
| Dimensions | |||
|---|---|---|---|
|
Bore (B1) |
1.2500 in |
B1 Max Shaft Penetration |
1.590 in |
|
Outer Diameter (OD) |
3.125 in (79.4 mm) |
Bore Tolerance |
+0.001 in / -0.000 in |
|
Hub Width (LH) |
1.590 in |
Length (L) |
4.379 in (111.2 mm) |
|
Recommended Shaft Tolerance |
+0.0000 in / -0.0005 in |
||
| Fastening Hardware | |||
|
Forged Clamp Screw |
M8 |
Number of Screws |
1 ea |
|
Screw Material |
Alloy Steel |
Screw Finish |
Black Oxide |
|
Hex Wrench Size |
6.0 mm |
Seating Torque |
39 Nm |
| Performance Specifications | |||
|
Torque Specifications |
Torque ratings vary with insert selection |
Misalignment |
Misalignment ratings vary with insert selection |
|
Maximum Speed |
8,000 RPM |
Moment of Inertia |
1.605 lb-in2 |
|
Full Bearing Support Required? |
Yes |
Recommended Inserts |
|
|
Zero-Backlash? |
Yes |
Balanced Design |
Yes |
|
Fail Safe? |
Yes |
||
| Additional Information | |||
|
Weight (lbs) |
1.097836 |
Temperature |
-10°F to 180°F (-23°C to 82°C) |
|
Material Specification |
2024-T351 Aluminum Bar |
Finish |
Bright |
|
Finish Specification |
Bright, No Plating |
Manufacturer |
Ruland Manufacturing |
|
Recommended Gap Between Hubs |
0.074 in (1.88 mm) |
Country of Origin |
USA |
|
UPC |
65432939434 |
UNSPC |
31163011 |
|
Tariff Code |
8483.60.8000 |
||
| Product Notes | |||
|
Note 1 |
Stainless steel hubs are available upon request. |
Note 2 |
Performance ratings are for guidance only. The user must determine suitability for a particular application. |
|
Note 3 |
Torque ratings for the couplings are based on the physical limitations/failure point of the spiders. Under normal/typical conditions the hubs are capable of holding up to the nominal torque of the spiders. Please consult technical support for more assistance. |
Prop 65 |
|
WARNING This product can expose you to the chemical Ethylene Thiourea, known to the State of California to cause cancer and birth defects or other reproductive harm. For more information go to | Dimensions | |||
|---|---|---|---|
|
Outer Diameter (OD) |
3.125 in (79.4 mm) |
||
| Performance Specifications | |||
|
Rated Torque |
2,760 in-lb (311.84 Nm) |
Angular Misalignment |
0.8° |
|
Peak Torque |
5,520 in-lb (623.7 Nm) |
Parallel Misalignment |
0.008 in (0.20 mm) |
|
Torsional Stiffness |
1850 lb-in/Deg (209.02 Nm/Deg) |
Moment of Inertia |
0.217711 lb-in2 (7.953 X 10-5 kg-m2) |
|
Axial Motion |
0.060 in (1.52 mm) |
Maximum Speed |
8,000 RPM |
|
Full Bearing Support Required? |
Yes |
Zero-Backlash? |
Yes |
|
Approximate Assembly Force (lbf) |
850 lbf |
Bearing Load at Max Parallel Misalignment (lbf) |
85 lbf |
| Additional Information | |||
|
Weight (lbs) |
0.187700 |
Temperature |
-10°F to 180°F (-23°C to 82°C) |
|
Material Specification |
Polyurethane 98 Shore A RED |
Finish Specification |
Plain |
|
Manufacturer |
Ruland Manufacturing |
UPC |
634529375976 |
|
Country of Origin |
USA |
Tariff Code |
8483.60.8000 |
|
UNSPC |
31163011 |
||
| Product Notes | |||
|
Note 1 |
Performance ratings are for guidance only. The user must determine suitability for a particular application. |
Note 2 |
Torque ratings for the couplings are based on the physical limitations/failure point of the spiders. Under normal/typical conditions the hubs are capable of holding up to the nominal torque of the spiders. In some cases especially when the smallest standard bores are used or where shafts are undersized slippage on the shaft is possible below the nominal torque of the spiders. Keyways are available to provide additional torque capacity in the shaft/hub connection when required. Please consult technical support for more assistance. |
| Dimensions | |||
|---|---|---|---|
|
Bore (B1) |
1.0000 in |
B1 Max Shaft Penetration |
1.590 in |
|
Outer Diameter (OD) |
3.125 in (79.4 mm) |
Bore Tolerance |
+0.001 in / -0.000 in |
|
Hub Width (LH) |
1.590 in |
Length (L) |
4.379 in (111.2 mm) |
|
Recommended Shaft Tolerance |
+0.0000 in / -0.0005 in |
||
| Fastening Hardware | |||
|
Forged Clamp Screw |
M8 |
Number of Screws |
1 ea |
|
Screw Material |
Alloy Steel |
Screw Finish |
Black Oxide |
|
Hex Wrench Size |
6.0 mm |
Seating Torque |
39 Nm |
| Performance Specifications | |||
|
Torque Specifications |
Torque ratings vary with insert selection |
Misalignment |
Misalignment ratings vary with insert selection |
|
Maximum Speed |
8,000 RPM |
Moment of Inertia |
1.625 lb-in2 |
|
Full Bearing Support Required? |
Yes |
Recommended Inserts |
|
|
Zero-Backlash? |
Yes |
Balanced Design |
Yes |
|
Fail Safe? |
Yes |
||
| Additional Information | |||
|
Weight (lbs) |
1.162485 |
Temperature |
-10°F to 180°F (-23°C to 82°C) |
|
Material Specification |
2024-T351 Aluminum Bar |
Finish |
Bright |
|
Finish Specification |
Bright, No Plating |
Manufacturer |
Ruland Manufacturing |
|
Recommended Gap Between Hubs |
0.074 in (1.88 mm) |
Country of Origin |
USA |
|
UPC |
65432939432 |
UNSPC |
31163011 |
|
Tariff Code |
8483.60.8000 |
||
| Product Notes | |||
|
Note 1 |
Stainless steel hubs are available upon request. |
Note 2 |
Performance ratings are for guidance only. The user must determine suitability for a particular application. |
|
Note 3 |
Torque ratings for the couplings are based on the physical limitations/failure point of the spiders. Under normal/typical conditions the hubs are capable of holding up to the nominal torque of the spiders. Please consult technical support for more assistance. |
Prop 65 |
|
